axp ordering information for pc board to flat cable pcb type connectors (axp) mini-dip type ic type features 1. high density mounting can be done. because of its 5.7mm high and low pro?e, its effectiveness for pc board mounting is broad. 2. labor saving in making connections is achieved. all terminals can be connected as a group in this pressure connection construction, and by means of the temporary cover stop, cable insertion is easily carried out, and connection labor is minimized. 3. compliance with rohs directive environmentally friendly, the connectors comply with europe s rohs directive. cadmium, lead, mercury, hexavalent, chromium, pbb and pbde are not used. lo w pro?e 5.7mm 8: au plating/au plating pcb type 4: mini-dip type 5: ic type (14, 16, 24, 40 contacts) 6: ic type (20 contacts) 2: standard terminal layout 6: reverse terminal layout axp 1 8 10: 10 contacts 14: 14 contacts 16: 16 contacts 20: 20 contacts 24: 24 contacts 26: 26 contacts 30: 30 contacts 34: 34 contacts 40: 40 contacts 50: 50 contacts 60: 60 contacts 64: 64 contacts 1: dip type all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
axp product types notes) 1. tray packaging: outer carton 200 pcs. 2. the upper surface of a connector with mini dip type standard pin layout is marked with axp4 2? connectors with reverse pin layout is marked with axp4 ? the orientation of the triangle distinguishes standard from reverse pin layouts. 3. the ic type pcb type connectors are reverse terminal layout only. 4. for available foreign standard products, refer to ?tandards chart on the end of the catalog. specifications 1. characteristics 2. material and surface treatment 3. applicable cable dimensions mm general tolerance: 0.3 no. of contacts mini-dip type ic type (reverse terminal layout) standard terminal layout reverse terminal layout 10 axp410218 axp410618 14 axp414218 axp414618 aXP514618 16 axp416218 axp416618 axp516618 20 axp420218 axp420618 axp620618 24 axp524618 26 axp426218 axp426618 30 axp430218 axp430618 34 axp434218 axp434618 40 axp440218 axp440618 axp540618 50 axp450218 axp450618 60 axp460218 axp460618 64 axp464618 item speci?ations conditions electrical characteristics rated current 1a breakdown voltage 650v ac for 1 min. detection current: 1ma insulation resistance min. 1,000m ? at 500v dc megger contact resistance max. 15m ? measured based on the hp4338b measurement method of jis c 5402 environmental characteristics ambient temperature ?5 c to +105 c vibration resistance 10 to 55hz at the double amplitude of 1.52mm no opening more than 1 sec. at max. 100ma carrying current shock resistance 490m/s 2 {50g} part name materials surface treatment molded portion glass reinforced pbt (ul94v-0) contact copper alloy ni plating on base, au plating on surface flat cable (stranded wire) pitch 1.27mm/conductor, awg28 (7 conductors/0.127 dia.) ?mini-dip type a b 0.25 2.54 c 7.0 8.2 5.6 5.2 3.5 0.6 2.54 0.5 6-0.8 dia. (when cover is temporarily fixed) recommended pc board pattern (bottom view) b 0.1 (a) (7.0) 2.54 0.1 0.9 0.05 dia. 2.54 0.1 dimension table (mm) no. of contacts abc 10 17.5 10.16 10.3 14 22.7 15.24 15.5 16 25.1 17.78 17.9 20 30.2 22.86 23.0 26 37.9 30.48 30.6 30 42.9 35.56 35.7 34 48.0 40.64 40.8 40 55.6 48.26 48.4 50 68.3 60.96 61.1 60 81.0 73.66 73.8 64 86.1 78.74 78.9 all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
axp ?ic type a b d e 0.25 c 8.2 5.2 3.5 0.6 2.54 0.5 3.6 dia. (when cover is temporarily fixed) recommended pc board pattern (bottom view) b 0.1 d 0.1 (a) (e) 2.54 0.1 0.9 0.05 dia. dimension table (mm) no. of contacts abcde 14 20.0 15.24 13.0 7.62 10.6 16 22.5 17.78 15.0 7.62 10.6 20 27.6 22.86 20.0 7.62 10.6 24 32.7 27.94 25.0 15.24 18.2 40 53.0 48.26 45.2 15.24 18.2 mm general tolerance: 0.3 cable no. and terminal position correlation drawing terminal layout terminal numbers are not indicated on the connector. when the cable numbers are temporarity assigned from the end as 1, 2, 3, 4......, the corresponding terminals are as shown in the drawing below. cable no. layout (top view) standard terminal layout reverse terminal layout cable no. 1 2 3 4 n-1 n6 5 4 3 2 1 n-1 n6 5 4 3 2 1 notes 1. regarding design of pc board the connector terminal numbers are not indicated. using the triangle mark on the cover as reference, the pc board design and the cable connections can be carried out. 2. regarding the soldering operation soldering should be carried out under the conditions given below. 260 c: within 10 seconds 300 c: within 5 seconds 350 c: within 3 seconds 3. regarding external force applied to the cable because no strain relief is provided for the pc board type connector, care should be taken not to apply external force to the cable. suf?ient slack should be provided in the cable length. 4. regarding handling of terminals care should be teken with the terminals because repeated bending of the terminals can lead to damage. 5. regarding handling of the cover after the cover has been inserted into the base, when it is to be removed, care should be teken not to apply excessive force to displace the radius section of the cover since that will cause damage. 6. regarding the cable pressure connection tool the special tool provided for cutting the cable and making the pressure connections should be used. regarding general notes, please refer to page 12. for other details, please verify with the product speci?ation sheets. all rights rese r v ed c o p y r i gh t matsushita elect r ic w o r k s , ltd.
|
